SSM26新一代聚脲密封膠

SSM26 New generation polyurea sealant

一、產品介紹Product information

SSM26新一代聚脲密封膠是德國Drache Handels UG 公司于二十一世研發的一種

以新型硅烷封端聚醚為主體樹脂的濕固化型高分子單液型產品，與空氣中濕氣反應生成類橡膠的彈性體，以達到灌封效果。因其高固含、不發泡、高粘結和親水反應的特點，該產品的密封效果比普通同類產品更優。同時該產品的低模量和高彈性使得其能有效解決變形縫、伸縮縫和交接縫等結構出現的滲漏問題。

SSM26 New generation of polyurea sealant is Drache Handels UG companyfrom Germany developed in the 21st century A new type of silane-terminated polyether is used as the main resin for wet curing polymer single liquid product, which reacts with the moisture in the air to form rubber-like elastomer to achieve the potting effect. Due to the characteristics of high solid content, non-foaming, high adhesion and hydrophilic reaction, the sealing effect of this product is better than that of ordinary similar products. At the same time, the low modulus and high elasticity of the product make it effective to solve the leakage problem of deformation joints, expansion joints and joint joints.

 

二、產品特性Product characteristics

? 耐久性好，耐老化、耐水泡、耐低溫、耐高溫

?可在水中固化

?一定的強度和優異的彈性，可很好的適應形變

?膠體內部結構致密，能有效防水

?濕固化時不會產生氣泡

?固化時對溫度不敏感，高溫與低溫均可固化

?單組份材料，施工簡單方便

?無溶劑產品，無味、無VOC揮發物。

 

? Good durability, aging resistance, blister resistance, low temperature resistance, high temperature resistance

? Can be cured in water

? Certain strength and excellent elasticity, can be well adapted to deformation

? The internal structure of the gel is dense and can effectively waterproof

? No bubbles during wet curing

? When curing, it is not sensitive to temperature, and can be cured at high and low temperatures

? Single component material, simple and convenient construction

? Solvent-free products, odorless, no VOC volatiles.

 

三、產品應用范圍Product application range

適用于道路、橋梁、房屋等伸縮縫的止水嵌縫密封和其他建筑變形縫、沉降縫防水密封。

It is suitable for sealing of expansion joints such as roads, Bridges and houses, and waterproof sealing of deformation joints and settlement joints of other buildings.

 

四、技術參數Technical parameter

產品物理屬性Physical property of product

項目	結果
外觀	白色
比重(g/cm3)	1.1
粘度（cps）@25℃	11000±1000
固含量（%）	98±2
表干時間（min）	30（25℃）
覆涂間隔（h）	最小6h；最大24h（25℃）

 

典型物理測試性能 Typical physical test performance  

項目	測試標準	結果
硬度（shoreA）	GB/T 22446-2009	55
拉伸強度MPa	GB/T 528-2009	1.5
100%拉伸模量	GB/T 528-2009	0.6
300%拉伸模量	GB/T 528-2009	1.0
斷裂伸長率%	GB/T 528-2009	400%
附著力（底材為混凝土）MPa	GB/T 22446-2009	1.3（或底材破壞）

 

產品相應固化時間Product curing time

基材溫度	表干	實干	完全固化
+10℃	40min	24h	7d
+20℃	30min	15h	7d
+30℃	20min	10h	7d

注：以上固化時間會因環境情況的變化而有所不同，尤其是溫度和相對濕度的變化。

Note: The above curing time will vary depending on environmental conditions, especially changes in temperature and relative humidity.

 

五、施工注意事項Construction precautions

? 施工設備及應用指導

手工刮板刮涂或灌注施工（疏松混凝土表面應進行預處理加強）

? Construction equipment and application guidance

Manual scraper scraping or pouring construction (loose concrete surface should be pre-treated to strengthen)

 

?施工環境 

環境溫度:-5~-+40℃

相對濕度：≤90%

露點：≥3℃

? Construction environment

Ambient temperature :-5~ +40℃ 

Relative humidity: ≤90%

Dew point: ≥3℃

 

?施工基層處理

金屬表面：建議噴砂除銹，達到ISO8501-1或GB8923標準的Sa2.5級。

混凝土表面：達到堅固、密實、平整、干凈、干燥狀態。不應有起砂、起殼、裂縫、蜂窩麻面等現象。

其它材質基層的應用處理可咨詢圣士曼技術人員。

? Construction base treatment

Metal surface: It is recommended to sand blast to remove rust, to ISO8501-1 or GB8923 standard Sa2.5.

Concrete surface: solid, dense, flat, clean, dry state. There should be no sand, shell, cracks, honeycomb and other phenomena.

The application of other material bases can be consulted by the Saint Si Man technicians.

 

?施工注意事項  

1、本產品可在零下10℃的低溫下使用。若在低溫環境中使用時，建議先將涂料桶放置在有空調房間中在高溫下保持24小時以上。

2、建議每次使用多少倒出多少，并及時將桶蓋密封，使用后的涂料不得再倒回原桶中。

3、填充縫隙時，可將本材料倒入三角塑料袋子，用扎帶扎緊。施工時將塑料袋尖角剪開直徑6-15mm的孔洞，沿著縫隙擠壓施工，將材料注入縫隙中。

4、若施工厚度較厚，建議2遍施工。每遍施工間隔時間在6-30小時內。

? Construction precautions

1, this product can be used at a low temperature of minus 10℃. If used in a low temperature environment, it is recommended to place the paint bucket in an air-conditioned room at high temperature for more than 24 hours.

2, it is recommended to pour out how much each time you use, and seal the bucket cover in time, and the paint shall not be poured back into the original bucket after use.

3. When filling the gap, the material can be poured into the triangular plastic bag and tied tightly with cable ties. During the construction, the sharp corners of the plastic bags are cut open holes with a diameter of 6-15mm, and the construction is squeezed along the gaps, and the materials are injected into the gaps.

4, if the construction thickness is thick, it is recommended to construct twice. Each construction interval is within 6-30 hours.

 

?產品包裝及保質期

包裝規格：   10公斤/桶

儲存環境溫度：5℃—35℃

產品保質期自生產日起并確保未開封的狀態下6個月(確保產品包裝密封完好)

在陰涼，通風的環境下儲存，避免陽光的直射

? Product packaging and shelf life

Packing specification: 10 kg/barrel

Storage ambient temperature: 5℃ -35℃ 

Product shelf life from the date of production and ensure unopened state of 6 months (ensure product packaging sealed)

Store in a cool, ventilated environment away from direct sunlight

 

?產品健康和安全信息

關于產品操作處置，儲存及廢棄處置的相關信息和建議，請參閱圣士曼公司最新版本的產品技術安全技術使用說明書（MSDS）。其中包括產品物理特性，生態學，毒理學資料及其他相關安全信息數據。

? Product health and safety information

For information and advice on handling, storage and disposal of products, please refer to the latest version of the MSDS for Product Technical Safety. This includes product physical characteristics, ecology, toxicology data and other relevant safety information data.

 

六、誠信聲明Statement of good faith

圣士曼公司承諾以上所列各項產品數據是在相關實驗室相對應標準測試獲取，測試過程中相關數據會因測試環境和方法不同而結果略有差異。因此圣士曼公司建議客戶使用該產品前做好實地考察論證。除產品質量本身外，圣士曼公司不承擔任何責任并保

證對以上數據進行調整和更新而不提前告知的權利，并請諒解。

The company promises that the above listed product data is obtained in the relevant laboratory corresponding to the standard test, and the relevant data will be slightly different due to the different test environment and method. Therefore, the company advises customers to conduct a field study before using the product. In addition to the quality of the product itself, the company does not assume any responsibility and guarantees the right to adjust and update the above data without prior notice.